







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Cabinets & Countertops in Spring Valley, NV: What to Expect
Cabinets & countertops in Spring Valley usually run $14,000 – $45,000 for a full replacement, and most jobs take two to four weeks from demo to final caulk. The bigger constraint here isn’t labor, it’s your homeowner association: door style, finish, and even countertop edge profile can sit inside an architectural review before a single box gets ordered. Call (844) 797-5026 and we’ll walk your community’s rules with you before you sign anything.
How We Run a Cabinet and Countertop Job, Start to Finish

Every job follows the same five stages. What changes is how much of your HOA review sits over the top of them, so we build the approval timeline into the schedule instead of pretending it doesn’t exist.
Stage 1: In-home measure and ARB packet (day 1 to day 5). We laser-measure the run, check wall plumb and floor level, and photograph the existing layout. You pick door style, color, and countertop material with your community’s approved palette in front of you. If your Spring Valley HOA requires an architectural request, we help assemble the drawings, finish samples, and spec sheet those committees want to see. This is the stage where a rushed decision costs you a rejection and a month.
Stage 2: Permit and ordering (week 1 to week 3). Because Spring Valley is unincorporated Clark County, the paperwork goes to Clark County Public Works and Building Department rather than a city hall. Cabinet lead times still run longer than many homeowners expect, so we lock the order the week measurements are approved. You approve the final shop drawing before anything is cut.
Stage 3: Demo and prep (2 to 4 days). Old cabinets come out, and we cap the water lines and make the electrical safe. Then the room gets what most bids skip: drywall patched to flat, any soft subfloor cut back and replaced, and wall surfaces primed. Cabinets installed over a wavy wall telegraph every flaw into the door reveals. We don’t do that.
Stage 4: Cabinet set (3 to 5 days). Base and wall boxes get shimmed plumb, screwed into studs, and lined up on the countertop plane. Crown and light rail go on, doors and drawers are adjusted, and hardware is drilled to your template. You walk it with us before the template guy arrives, because moving a box after the countertop is cut is a rebuild.
Stage 5: Template, fabrication, install (5 to 10 days). The countertop fabricator templates the actual installed cabinets, cuts the slab with sink and cooktop openings, and returns to set it. Then the final hookups, caulk lines, and punch walk. The gap between template and install is where most schedules slip, so we book the fabricator before demo day, not after.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Actually Choose Between
Most of the decision lives in three questions: what the boxes are made of, what the top is made of, and how the doors operate. Here’s the honest trade-off on each.
- Cabinet construction – plywood vs. particleboard boxes. Plywood holds screws and handles the dry Mojave air without swelling at the joints; particleboard costs less and is fine in a dry room, but it doesn’t like a slow leak under the sink. We lean plywood on any run near a water line.
- Door material – painted MDF vs. solid wood vs. thermofoil. Painted MDF gives the cleanest shaker look for the money and can be touched up; solid wood takes a stain and dents less; thermofoil is the budget pick and the one we see peeling on older Spring Valley tract kitchens when a cabinet sits near the oven.
- Countertop – quartz, granite, or a solid-surface option. Quartz is the low-maintenance favorite because it doesn’t need sealing. Granite costs similar to quartz in most grades and hides more, but it wants periodic sealing. Cambria quartz is a brand we specify often when a homeowner wants a consistent, engineered slab.
- Door and drawer operation – standard vs. soft-close. Soft-close hinges and undermount slides add a few hundred dollars across a kitchen and are the single most-requested upgrade. They also cut the cabinet slam that carries through a shared-wall condo.
- Sink and faucet spec. An undermount sink needs a fabricator who will polish the cutout edge; a drop-in saves on fabrication. We fit Kohler and American Standard fixtures regularly, and the sink decision has to happen before the template, not after.
What Cabinets & Countertops Cost in Spring Valley, NV

A cabinet replacement alone runs $4,000 – $13,000 in Spring Valley, and a countertop installation adds $2,000 – $6,500. Put them together and most homeowners land in the $14,000 – $45,000 band, with the spread driven by a handful of real variables rather than guesswork.
Five things move the number:
- Linear feet and layout. A galley with 15 linear feet sits at the floor of the range. A U-shaped kitchen with an island and a pantry run climbs toward the ceiling.
- Material grade. A thermofoil-and-laminate job and a plywood-box, painted-MDF, quartz-slab job are both “new cabinets and countertops” and they are not the same price.
- Relocating plumbing or electrical. Moving a sink, adding a dedicated circuit for a new range, or shifting a dishwasher bay adds both trade cost and inspection scope. Keeping fixtures in place is the cheapest path.
- Existing condition. Water damage under a sink, a soft subfloor, or a wall out of plumb by an inch all add prep days.
- Permit scope and HOA review. A like-for-like swap may not trigger a permit, but a layout change does, and an ARB submission can push the calendar.
Every written estimate is line-item: boxes, doors, hardware, countertop slab and fabrication, demo, prep, and permit. What isn’t included is spelled out too, so nothing shows up on the final invoice that wasn’t on the first page. See the full scope on our Kitchen Remodeling service page.
See the difference
Before
After
Before
After
Before
AfterWhat Spring Valley Homes Do to a Cabinet Job
Spring Valley is unincorporated Clark County, so permits move through Clark County Public Works and Building Department, not a city hall. That matters because there’s no municipal layer to shortcut, and county inspectors hold projects to dust-control and erosion rules on even small jobs. In the 1990s and 2000s master-planned subdivisions around Rhodes Ranch and along the 215 beltway, most of the housing stock is stucco-over-wood-frame tract construction, and we see the same things on those kitchens: particleboard boxes swelling under a slow sink leak, thermofoil peeling near the range, and tile countertops grouted to the wall that no one wants to clean anymore. Where a homeowner is replacing cabinets as part of a full Kitchen Remodeling in Spring Valley, those issues fold into a larger scope. If you’d rather add square footage than squeeze it out of the same four walls, some homeowners often pair this with a Garage Conversion ADU in Spring Valley or a New Detached ADU in Spring Valley instead of rebuilding the existing kitchen. We cover all of Spring Valley, ZIP 89113 included, and we build the ARB review into the schedule from day one. Our technicians have up to 12 years of experience.
Serving Spring Valley, NV – Our Local Coverage Area
We serve Spring Valley and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked in Spring Valley

Two to four weeks on site, plus cabinet lead time and your HOA’s review window. Demo eats 2 – 4 days, cabinet set 3 – 5, and the countertop template-to-install gap is typically 5 – 10 days. Call (844) 797-5026 for a schedule built around your community’s approval timeline.
Usually not for a like-for-like swap, but yes once you move plumbing, electrical, or walls. Since Spring Valley runs through Clark County rather than a city building department, we confirm what your specific scope triggers before demo. Call (844) 797-5026 and we’ll tell you straight.
That depends on your community’s architectural guidelines, and it’s the first thing we check. Many Spring Valley HOAs publish an approved palette and want finish samples and a spec sheet before work starts. We help assemble that packet so you don’t get flagged for a door style or exterior-visible finish. Call (844) 797-5026 to start.
Cabinet replacement runs $4,000 – $13,000, countertops $2,000 – $6,500, and a combined job typically lands at $14,000 – $45,000. Grade, layout, and moving fixtures push the number either way. Call (844) 797-5026 for a free line-item estimate.
Yes. Every cabinet and countertop job is covered by our 730-Day Done Right Promise: if it isn’t done right, we make it right. That covers our installation workmanship. Call (844) 797-5026 with any questions before you commit.
Get Your Free Spring Valley Cabinet and Countertop Estimate
Call (844) 797-5026 for a free on-site estimate. We’ll measure the run, look at what’s behind the old cabinets, review your HOA’s approved finishes with you, and hand you a written line-item quote with a fixed number. A live person answers around the clock, so there’s no voicemail and no waiting until Monday. No-hassle upfront pricing, 0% financing for 18 months, and $1,000 off projects over $10,000.
Written by the team at Groundwork Construction Co.












